JET — JET JWL-1640EVS manual_en-de-fr 2016
Complete operating manual for the JET JWL-1640EVS wood lathe, delivering comprehensive guidance on installation, operation, and maintenance of this machine. The manual opens with CE conformity documentation and warranty terms, followed by an in-depth safety section addressing authorized use, general precautions, and residual hazards inherent to woodturning work. Technical specifications provide a detailed breakdown of the machine's construction—motor, headstock, tailstock, bed, and tool rest assembly—alongside complete performance data. Transportation and setup instructions walk through unpacking, assembly, electrical connection, and dust collection configuration. The operation section explains proper working postures, tool selection, spindle speed control, and essential turning techniques covering spindle work, bowl turning, and sanding and finishing methods. A dedicated setup and adjustments section covers spindle speed changes, spindle locking mechanisms, headstock rotation, and work-holding installation. Maintenance guidance addresses bed clamping adjustments and replacement procedures for belts and bearings. Troubleshooting and environmental protection information round out the manual, ensuring operators have the technical knowledge needed for safe and effective machine performance. Table of Contents: - R Tool caddy with tools - S Casting stands - 4.2 Technical data - Swing over bed - Centre distance - Number of mechanical speeds - Spindle speed range 1 - 40-1200 rpm - Spindle speed range 2 - 100-3200 rpm - Spindle nose - M33x3.5 DIN 800 - Headstock spindle taper - Headstock spindle bore - Spindle index lock - Headstock-Rotation - Tailstock spindle taper - Tailstock bore - Tailstock ram travel - Centre above floor - Overall (LxWxH) - 1854 x 508 x 1334 mm - Net weight - Mains - 1~230V, PE, 50Hz - Output power - 1.1 kW (1.5 HP) S1 - Reference current - Extension cord (H07RN-F): - 3x1.5mm² - Installation fuse protection - Protection class - 4.3 Noise emission - Acoustic pressure level (according to EN ISO 11202): - Idling - LpA 72.5 dB(A) - In operation - LpA 78.4 dB(A) - The specified values are emission levels and are not - necessarily to be seen as safe operating levels. - As workplace conditions vary, this information is intended to - allow the user to make a better estimation of the hazards and - risks involved only. - 4.4 Content of delivery - Lathe bed with headstock, tool support and tailstock – A - 350mm Tool rest – B - Legs – C - Spur centre – D - Live centre – E - Live centre with cone – F - Live centre pin – G - Knockout rod – H - 75mm Faceplate – J (installed on lathe) - Tool rest extension – K - Faceplate wrench – L - Levellers – M - Tool shelf – N - Socket hd. cap screws, 5/16”x1-1/4” – HP1* - Lock washers, 5/16” – HP2* - Flat washers, 5/16” – HP3* - Socket hd. cap screws, 3/8”x1-1/4” – HP4 - Lock washers, 3/8” – HP5 - User manual - Parts list - * included in hardware package JWL1440-HP1 - Fig 2 - 5. Transport and start up - 5.1 Transport and installation - The machine is designed to operate in closed rooms and - must be placed stable on firm and levelled ground. - The machine can be bolted to the floor if required. - For packing reasons the machine is not completely - assembled. - 5.2 Assembly - If you notice transport damage while unpacking, notify your - supplier immediately. Do not operate the machine! - Dispose of the packing in an environmentally friendly manner. - Clean all rust protected surfaces with a mild solvent. - Attach the leg stand : - At this point the headstock, tailstock and tool rest should be - removed. - Unscrew the stud (N, Fig 3) from each end of bed.
